Difference between revisions of "Async kb"

From Felixl.com
Jump to navigationJump to search
 
(→‎Session Granted)
 
(29 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
Terms:
 +
 +
''connection'': data transfer session, highest in hierarchy
 +
 +
''block'': data transfer unit, consists of several frames
 +
 +
''frame'': lowest data transfer unit. basically -- one network message
 +
 +
 +
 
Message type ==  
 
Message type ==  
 
* 0x80 = data
 
* 0x80 = data
Line 5: Line 15:
 
----------------
 
----------------
 
commands:
 
commands:
 +
 +
== Request Session ==
  
 
.data[0] = 0xca -- request session
 
.data[0] = 0xca -- request session
 +
 +
parameters:
 +
 +
.data[1] =  priority (always 1)
 +
 +
.data[2] , .data[3] -- data frame payload max size  (16 bit, big endian) (excluding frame id and total frame count)
 +
 +
== Session Granted ==
 +
 +
.data[0] = 0xf2 -- session granted
 +
 +
parameters:
 +
 +
.data[1] = number of frames per block
 +
 +
.data[2] = revision (always 0x01)
 +
 +
.data[3] = priority acknowledge (should reply with the same priority requested)
 +
 +
.data[4] .data[5] = bytes per data frame (maximum allowed bytes per frame, 16bit, bigendian), excluding frameid and frame total count
 +
 +
.data[6] .data[7] = number of microseconds between messages  -- don't bother about it
 +
 +
== Starting Transfer ==
 +
 +
.data[0] = 0xfd
 +
 +
no parameters
 +
 +
== Frame Acknowledge ==
 +
 +
.data[0] = 0xfa  (frame acknowledge)
 +
 +
parameters
 +
 +
.data[1]= total number of frames in this block
 +
 +
.data[2]= id of received message
 +
 +
.data[3]= id of current block
 +
 +
== Frame Not Acknowledged ==
 +
 +
.data[0] = 0xfa
 +
 +
.data[1] = 0x00
 +
 +
.data[2] = 0x00
 +
 +
params :
 +
 +
.data[3] = id of current block
 +
 +
== Single Frame Request ==
 +
 +
.data[0] = 0xfb
 +
 +
.data[1] = 0x00
 +
 +
parameters:
 +
 +
.data[2] = id of requested frame in current block
 +
 +
== Current block request ==
 +
 +
.data[0] = 0xfb
 +
 +
.data[1] = 0x00
 +
 +
.data[2] = 0x00
 +
 +
== Multiple Frame Request ==
 +
 +
.data[0] = 0xff
 +
 +
 +
.data[1] .... .data[msg.length-1] == id's of requested frames
 +
 +
== End of transfer ==
 +
 +
.data[0] = 0xf3
 +
 +
.data[1] = 0x00
 +
 +
parameters:
 +
 +
.data[2] = result -- 0x00 -- everything was ok, 0xff -- something went BAD
 +
 +
== Abort connection ==
 +
 +
.data[0] = 0xfc
 +
 +
.data[1] = 0x00
 +
 +
.data[2] = 0xff
 +
 +
send by receiver to abort connection.
 +
 +
== Adjust framerate ==
 +
 +
.data[0] = 0xf0
 +
 +
 +
don't bother about this command :)
 +
 +
== Suspend transfer ==
 +
 +
.data[0] = 0xfe
 +
 +
.data[1] = 0x00
 +
 +
parameters:
 +
 +
.data[2] = event.
 +
 +
 +
Events:
 +
 +
*0x00-0x01 -- Reserved (not used)
 +
*0x02-0x7f -- Priority info (when requested priority is less than current available)
 +
*0x80 - Reserved (not used)
 +
*0x81 - '''0-Frame''' received, but the receiver is busy with another connection
 +
*0x82 - '''0-Frame''' received, but the receiver don't have free buffer at the moment
 +
*0x83-0xff -- Reserved (not used)
 +
 +
== Keep Session Alive ==
 +
 +
.data[0] = 0xf1
 +
 +
.data[1] = 0x00
 +
 +
parameters:
 +
 +
.data[2] = Event
 +
 +
Events:
 +
*0x00-0x01 Reserved (not used)
 +
*0x02-0x7f Priority (this session has less priority than available)
 +
*0x80-0x82 Reserved (not used)
 +
*0x83 -  Data has been transmitted successfully, keep session alive, but no new data is ready yet
 +
*0x84 -  Transmitter is busy with another session.
 +
*0x85-0xff Reserved (not used)
 +
 +
== Data Frame ==
 +
 +
.data[0] = frame id
 +
 +
.data[1] = number of frames in current block (not including '''0-Frame''')
 +
 +
.data[2] .... .data[N] == user data
 +
 +
 +
There are 2 different frame types --- '''"0-Frame"''' and '''Regular Frame'''
 +
 +
'''0-Frame''' is the first frame to be send out -- it has description of current block transfer.
 +
 +
'''0-Frame''' has following structure:
 +
 +
.data[0]=0x00
 +
 +
.data[1]=number of frames in current block (not including '''0-Frame''')
 +
 +
.data[2]=0x00
 +
 +
.data[3]=Flags ( 0x01 == acknowledge after the entire block, 0x02 = acknowledge every frame)
 +
 +
.data[4]=total block count
 +
 +
== Communication Protocols ==
 +
Sender (TX)
 +
 +
Receiver (RX)
 +
 +
Simple transfer with block ack:
 +
 +
TX:Request Session
 +
RX:Session Granted
 +
TX:Starting Transfer
 +
TX:0-Frame (one block, 4 frames, ack after block)
 +
TX:Frame #1
 +
TX:Frame #2
 +
TX:Frame #3
 +
TX:Frame #4
 +
RX:Frame Acknowledge
 +
TX:End of tranfer
 +
TX:End of tranfer
 +
TX:End of tranfer
 +
 +
Simple transfer with frame ack:
 +
 +
TX:Request Session
 +
RX:Session Granted
 +
TX:Starting Transfer
 +
TX:0-Frame (one block, 4 frames, ack after every frame)
 +
TX:Frame #1
 +
RX:Frame Acknowledge
 +
TX:Frame #2
 +
RX:Frame Acknowledge
 +
TX:Frame #3
 +
RX:Frame Acknowledge
 +
TX:Frame #4
 +
RX:Frame Acknowledge
 +
TX:End of tranfer
 +
TX:End of tranfer
 +
TX:End of tranfer
 +
 +
Transfer with Suspend Transfer
 +
 +
TX:Request Session
 +
RX:Session Granted
 +
TX:Starting Transfer
 +
TX:0-Frame (one block, 4 frames, ack after block)
 +
RX:Suspend Transfer (event = busy with another transfer)
 +
RX:Frame Acknowledge(frame id 0, block id= current block)
 +
TX:Frame #1
 +
TX:Frame #2
 +
TX:Frame #3
 +
TX:Frame #4
 +
RX:Frame Acknowledge
 +
TX:End of tranfer
 +
TX:End of tranfer
 +
TX:End of tranfer
 +
 +
Transfer with Keep Session Alive
 +
 +
TX:Request Session
 +
RX:Session Granted
 +
TX:Starting Transfer
 +
TX:0-Frame (one block, 4 frames, ack after block)
 +
TX:Frame #1
 +
TX:Frame #2
 +
TX:Frame #3
 +
TX:Frame #4
 +
RX:Frame Acknowledge
 +
TX:Keep Session Alive (event = waiting for more data)
 +
TX:0-Frame (one block, 4 frames, ack after block)
 +
TX:Frame #1
 +
TX:Frame #2
 +
TX:Frame #3
 +
TX:Frame #4
 +
RX:Frame Acknowledge
 +
TX:End of tranfer
 +
TX:End of tranfer
 +
TX:End of tranfer

Latest revision as of 13:46, 15 March 2007

Terms:

connection: data transfer session, highest in hierarchy

block: data transfer unit, consists of several frames

frame: lowest data transfer unit. basically -- one network message


Message type ==

  • 0x80 = data
  • 0x90 = command

commands:

Request Session

.data[0] = 0xca -- request session

parameters:

.data[1] = priority (always 1)

.data[2] , .data[3] -- data frame payload max size (16 bit, big endian) (excluding frame id and total frame count)

Session Granted

.data[0] = 0xf2 -- session granted

parameters:

.data[1] = number of frames per block

.data[2] = revision (always 0x01)

.data[3] = priority acknowledge (should reply with the same priority requested)

.data[4] .data[5] = bytes per data frame (maximum allowed bytes per frame, 16bit, bigendian), excluding frameid and frame total count

.data[6] .data[7] = number of microseconds between messages -- don't bother about it

Starting Transfer

.data[0] = 0xfd

no parameters

Frame Acknowledge

.data[0] = 0xfa (frame acknowledge)

parameters

.data[1]= total number of frames in this block

.data[2]= id of received message

.data[3]= id of current block

Frame Not Acknowledged

.data[0] = 0xfa

.data[1] = 0x00

.data[2] = 0x00

params :

.data[3] = id of current block

Single Frame Request

.data[0] = 0xfb

.data[1] = 0x00

parameters:

.data[2] = id of requested frame in current block

Current block request

.data[0] = 0xfb

.data[1] = 0x00

.data[2] = 0x00

Multiple Frame Request

.data[0] = 0xff


.data[1] .... .data[msg.length-1] == id's of requested frames

End of transfer

.data[0] = 0xf3

.data[1] = 0x00

parameters:

.data[2] = result -- 0x00 -- everything was ok, 0xff -- something went BAD

Abort connection

.data[0] = 0xfc

.data[1] = 0x00

.data[2] = 0xff

send by receiver to abort connection.

Adjust framerate

.data[0] = 0xf0


don't bother about this command :)

Suspend transfer

.data[0] = 0xfe

.data[1] = 0x00

parameters:

.data[2] = event.


Events:

  • 0x00-0x01 -- Reserved (not used)
  • 0x02-0x7f -- Priority info (when requested priority is less than current available)
  • 0x80 - Reserved (not used)
  • 0x81 - 0-Frame received, but the receiver is busy with another connection
  • 0x82 - 0-Frame received, but the receiver don't have free buffer at the moment
  • 0x83-0xff -- Reserved (not used)

Keep Session Alive

.data[0] = 0xf1

.data[1] = 0x00

parameters:

.data[2] = Event

Events:

  • 0x00-0x01 Reserved (not used)
  • 0x02-0x7f Priority (this session has less priority than available)
  • 0x80-0x82 Reserved (not used)
  • 0x83 - Data has been transmitted successfully, keep session alive, but no new data is ready yet
  • 0x84 - Transmitter is busy with another session.
  • 0x85-0xff Reserved (not used)

Data Frame

.data[0] = frame id

.data[1] = number of frames in current block (not including 0-Frame)

.data[2] .... .data[N] == user data


There are 2 different frame types --- "0-Frame" and Regular Frame

0-Frame is the first frame to be send out -- it has description of current block transfer.

0-Frame has following structure:

.data[0]=0x00

.data[1]=number of frames in current block (not including 0-Frame)

.data[2]=0x00

.data[3]=Flags ( 0x01 == acknowledge after the entire block, 0x02 = acknowledge every frame)

.data[4]=total block count

Communication Protocols

Sender (TX)

Receiver (RX)

Simple transfer with block ack: 

TX:Request Session
RX:Session Granted
TX:Starting Transfer
TX:0-Frame (one block, 4 frames, ack after block)
TX:Frame #1
TX:Frame #2
TX:Frame #3
TX:Frame #4
RX:Frame Acknowledge
TX:End of tranfer
TX:End of tranfer
TX:End of tranfer

Simple transfer with frame ack: 

TX:Request Session
RX:Session Granted
TX:Starting Transfer
TX:0-Frame (one block, 4 frames, ack after every frame)
TX:Frame #1
RX:Frame Acknowledge
TX:Frame #2
RX:Frame Acknowledge
TX:Frame #3
RX:Frame Acknowledge
TX:Frame #4
RX:Frame Acknowledge
TX:End of tranfer
TX:End of tranfer
TX:End of tranfer

Transfer with Suspend Transfer 

TX:Request Session
RX:Session Granted
TX:Starting Transfer
TX:0-Frame (one block, 4 frames, ack after block)
RX:Suspend Transfer (event = busy with another transfer)
RX:Frame Acknowledge(frame id 0, block id= current block)
TX:Frame #1
TX:Frame #2
TX:Frame #3
TX:Frame #4
RX:Frame Acknowledge
TX:End of tranfer
TX:End of tranfer
TX:End of tranfer

Transfer with Keep Session Alive 

TX:Request Session
RX:Session Granted
TX:Starting Transfer
TX:0-Frame (one block, 4 frames, ack after block)
TX:Frame #1
TX:Frame #2
TX:Frame #3
TX:Frame #4
RX:Frame Acknowledge
TX:Keep Session Alive (event = waiting for more data)
TX:0-Frame (one block, 4 frames, ack after block)
TX:Frame #1
TX:Frame #2
TX:Frame #3
TX:Frame #4
RX:Frame Acknowledge
TX:End of tranfer
TX:End of tranfer
TX:End of tranfer
Retrieved from "https://felixl.com/index.php?title=Async_kb&oldid=1489"